EDUCATION / ARTICLE
O-Level Physics Heating: Split Temperature Changes From Changes of State
TestPapersFree · 2026-11-17 08:07:14
A student in a public SGExams discussion asked for help with thermal-properties calculations. The difficulty is familiar: two equations seem relevant, and choosing one without describing the physical change leads to an incomplete answer. Write a short journey for the substance before substituting numbers.
The official 2026 O-Level Physics 6091 syllabus, under Thermal Properties of Matter, includes specific heat capacity, specific latent heat and their energy relationships. This article focuses on that stated syllabus. The examples are original and are not answers to a particular national examination paper.
Describe the starting and finishing states
Consider 0.20 kg of water initially at 25°C. It is changed completely into steam at 100°C at atmospheric pressure. For this exercise, take the specific heat capacity of water as 4,200 J kg−1 °C−1 and its specific latent heat of vaporisation as 2.26 × 106 J kg−1. Ignore the container's energy gain and losses to the surroundings.
The first stage is liquid water warming from 25°C to 100°C. The second stage is water changing from liquid to gas at 100°C. The final state matters: reaching the boiling temperature does not mean all the water has already become steam.
Calculate one energy contribution per stage
For the temperature rise, use Q = mcΔT. Here ΔT = 100 − 25 = 75°C. The energy is 0.20 × 4,200 × 75 = 63,000 J. This accounts for warming the liquid only.
For vaporisation, use Q = mL. The energy is 0.20 × 2.26 × 106 = 452,000 J. Both stages are necessary, so the total required energy is 63,000 + 452,000 = 515,000 J, or 515 kJ. A calculation using only mL would omit the initial warming.
Notice that the vaporisation contribution is much larger here. That observation is a check on these particular numbers, not a rule that every change-of-state contribution must dominate every temperature-change contribution.
Understand the flat section of a heating curve
In the idealised boiling stage for a pure substance at constant pressure, energy is supplied while temperature remains constant. The energy changes the particles' arrangement and separation rather than raising the temperature. A flat temperature section therefore does not mean zero energy transfer.
Ask a useful diagnostic question: if the heater stays on during boiling, where does the transferred energy go? An answer should connect the energy to the change of state. Avoid claiming that the particles stop moving or that all heating must produce a temperature increase.
Bring power into the calculation afterwards
Suppose the heater supplies 1,000 W, with all that power transferred to the water in our idealised example. Since one watt is one joule per second, the time is 515,000 ÷ 1,000 = 515 seconds. This is 8 minutes 35 seconds. Use the total energy for the entire process, rather than the energy for just the boiling stage.
If a different version says that only 80% of the electrical input reaches the water, the useful heating power is 800 W. The time becomes 515,000 ÷ 800 = 643.75 seconds, approximately 644 seconds. Efficiency is a supplied condition in that version; do not invent a percentage when the question gives none.
Keep the mass and the units attached to each stage
If the question gives 200 g, convert it to 0.20 kg before using the stated constants. If only part of the water vaporises, the mass in mL is the mass that changes state. It need not equal the mass warmed initially. Similarly, steam heated above 100°C would require another stage and suitable specific-heat-capacity data.
For practice, select a thermal question from the Secondary Pure Physics collection. Before looking at the solution, write the starting state, each intermediate state and the finishing state. Put one equation beside each transition. Check the answer by confirming that every physical stage is represented and that the units reduce to the quantity requested.
Add Comment
This policy contains information about your privacy. By posting, you are declaring that you understand this policy:
This policy is subject to change at any time and without notice.
These terms and conditions contain rules about posting comments. By submitting a comment, you agree with these rules:
Failure to comply with these rules may result in being banned from submitting further comments.
These terms and conditions are subject to change at any time and without notice.
Comments