TestPapersFreeTHE EDUCATION COLLECTION
SINGAPORE EXAMINATION PAPERS
Primary · Secondary · Junior College
Browse schools

THE SCHOOL DIRECTORY

Primary schools 35
Secondary schools 123
Junior College schools 23
Levels, subjects & past years

Primary

Secondary

Junior College

Explore Singapore school collections, subjects and past years.

EDUCATION / ARTICLE

H2 Physics Solenoids: Convert Total Turns to Turns per Metre

TestPapersFree · 2026-11-21 08:06:02

After the revised 2026 H2 Physics Paper 2, a student asked how others used the formula to find the solenoid’s magnetic flux density. The formula sheet gets you as far as B = μ0nI. The next decision is what the question gives you for the windings and whether you need to calculate n yourself. SGExams solenoid calculation discussion

Match the formula to the field you are finding

For an ideal long, air-core solenoid, the expression B = μ0nI gives the field magnitude inside, away from the ends. Here μ0 is the permeability of free space, I is the current and n is the number of turns per unit axial length. If the question gives N turns in a uniformly wound length L, substitute n = N/L. For n in m−1, measure L in metres along the solenoid. Use the length covered by the stated turns.

The revised syllabus lists separate expressions for a long straight wire, a flat circular coil and a long solenoid. A flat coil’s radius matters for the field at its centre. For the ideal long-solenoid expression, the relevant winding quantity is turns per metre. The syllabus also covers sketching the field and recognising that a ferrous core can influence it. SEAB 9478 H2 Physics syllabus, section 17 and formulae

Put the unit conversion on its own line

Consider a long air-core solenoid with 600 turns uniformly wound over 30 cm, carrying 1.5 A. Start with L = 0.30 m. The turn density is 600 ÷ 0.30 = 2000 m−1. A quick estimate confirms the size. There are 600 turns in less than one metre, so the number of turns per metre must exceed 600. Now substitute μ0 = 4π × 10−7 H/m. The field magnitude is (4π × 10−7) × 2000 × 1.5 ≈ 3.8 × 10−3 T, or 3.8 mT to two significant figures.

Suppose the same number of turns is spread over twice the axial length and the current is also doubled. The turn density halves to 1000 m−1, while the current rises to 3.0 A. The product nI stays the same, so the two ideal solenoids give the same field magnitude. If the length doubles while the current is held fixed, the field halves. This comparison lets you check a claimed change before entering any numbers.

Work out direction from the winding

Use the right-hand grip rule with conventional current. Curl the fingers of your right hand around the turns in the direction of that current. Your thumb points along the magnetic field inside the solenoid. Viewed straight on from one end, anticlockwise current means the interior field points towards you at that end. Reversing the current reverses the field. If the size of the current stays the same, the field magnitude stays the same in the ideal model.

When drawing the field, use approximately parallel lines in the middle of a long solenoid. Show the lines curving around outside to complete the loops. The approximation applies to the central region. A sketch that shows the lines bending near the ends is consistent with using the uniform-field approximation well inside the coil.

Practise recognising a turn density that is already given

A second long air-core solenoid has eight turns per centimetre and carries 2.0 A. Multiply eight by 100 to get 800 turns per metre. The field is about 2.0 mT. Because the question already gives a turn density, the conversion to metres completes the calculation of n. In a prelim question, mark the field location, label the winding data as N or n, then use the appropriate expression and add a direction if asked. JC H2 Physics test papers

← More articles

Add Comment

* Required information
1000

Comments

No comments yet. Be the first!

ONE COLLECTION. EVERY STAGE.

Find your next practice paper.

PRIMARY

Strong foundations.

Explore Primary school papers →

SECONDARY

The next step.

Explore Secondary school papers →

JUNIOR COLLEGE

A wider horizon.

Explore Junior College school papers →